Your cart is empty.
Your cart is empty.This bezel and keypad assembly kit is designed to use with Hayward Universal H-Series Low NOx pool heater models H150FDN, H150FDP, H200FDN, H200FDP, H250FDN, H250FDP, H300FDN, H300FDP, H350FDN, H350FDP, H400FDN, H400FDP. Weighs 17 pounds.
Alan V Cuevas
Reviewed in the United States on February 22, 2025
Worked as it's supposed to
Barbara
Reviewed in the United States on September 18, 2024
Key pad does not function correctly. Was wait for pool service to install. Faild
Ted Leptick
Reviewed in Canada on July 5, 2024
Worked well. Fit the unit perfectly.
Sandy Harvey
Reviewed in the United States on April 25, 2024
Didn’t realize how bad our previous panel was until we got this one. Super easy to install and can now see everything again!
John
Reviewed in Canada on April 19, 2024
Arrived as promised and fits perfectly on my Hayward 300.
Sonya Gauthier
Reviewed in Canada on May 19, 2022
Easy to install. Excellent product. 2 minutes to install.
MR-2018
Reviewed in Canada on August 24, 2018
Easy to install the plate, however, it was not clear to me that the control board was a separate purchase. After installation of the control board bought afterwards, everything is back to normal.
Bcampbell2323
Reviewed in the United States on August 22, 2018
I bought the plastic outer panel and the Hayward display board that was showing the CE error message and another part (Hayward FDXLICB1930 FD Integrated Control Board Replacement Kit for Select H-Series Pool Heater) which I didn’t need $185.00. All I can tell you is it took me 10 minuets and that includes the time walking to the fridge to grab a beer. Great vendor, great service, fair price and I’m up and running. Thank you to the previous buyers with their posts, pictures and advice. Turn the power off, take a few pictures but it’s very simple. I hope this helps
Floyd L.
Reviewed in Canada on August 23, 2017
The keypad assembly was easy to install and works perfectly. I am very happy with it. Thank you very much amazon. Floyd.
CSXGM
Reviewed in the United States on November 3, 2017
Arrived on time. Inatalled in less then 5 minutes. Steps were:Turn power off to unitRemove cover by taking out 4 phillips head screwsRemove circuit board from cover by taking out 2 phillips head screwsDisconnect the ribbon connector from coverTo install reverse removal procedureA couple of notes, if you need a.circuit board ( I did not) it is sold separatelyThe cover comes with the gasket already installed so don't order one. My only complaint is that at $54 it ia a pretty expensive piece of plastic
John
Reviewed in the United States on July 28, 2014
My Keypad was damaged by the sun. The buttons on the display no longer functioned properly. The model replacement for my heater was no longer manufactured, but this unit is it's replacement. I performed the following steps to replace the display unit.It was easy and worked well.I turned off the powerRemoved the old display unit from the heater by removing the 4 associated screwsDisconnected the display from the backing PC board by disconnecting the ribbon cable connectorRemoved the PC board from the back of the old display unit by removing the associated screwsPlaced the PC board on the new display unit in the same placeRe-inserted and tightened the associated screws that hold the PC BoardRe-connected the display's ribbon cable to the PC BoardReattached the display unit to the heater using the associated screwsTurned on the Power - The worked fine, no issues!
Brian Ziegler
Reviewed in the United States on June 24, 2014
The keypad on my Dad's pool heater went out. The repair guy quoted an outrageous amount for the part from his central office. He was a good guy and suggested I do it myself and gave me a few tips.It can be a challenge to figure out which Amazon part matches the Hayward part sheet. I can confirm that this is in fact "29 FDXLBKP1930 Bezel and Keypad Assembly, Taupe". It is also a little unclear what you are getting. This is the keypad that attaches to the "28 IDXL2DB1930 Display Board Only" via two screws and a ribbon cable. In my case it was very easy to unscrew the display board, disconnect the ribbon cable, discard the old keypad, connect the ribbon cable to the new keypad and reattach the existing display board to the new keypad.The keypad comes with a fresh rubber gasket. I had to push it around a bit to get the holes in the gasket properly aligned with the holes in the keypad bezel. I had to use a lot of thumb pressure to line up the holes on the keypad and the heater housing while trying to screw in the retaining screws at the same time. Nothing cracked or warped and the new pad worked like a charm when I tried it.
Marnie
Reviewed in the United States on May 15, 2014
This keypad assembly was a replacement for one on our pool heater that had problems because the heat here in Southern CA got to it. It's just like our old one, so we anticipated having the same problem again. My husband suggested making some kind of cover for it to shield it from direct sunlight--hinged so it could be flipped up when we wanted to use the controls. Stumped by the need for something lightweight, but opaque, and that would also fit due to the angle of the bezel and its placement on the heater, I suggested using a plastic pan (originally bought to develop photos). He cut it to fit, mounted it, and it has worked wonderfully ever since.
Recommended Products
$29.99
$ 12 .99 $12.99