Your cart is empty.
Your cart is empty.1/4" O.D. lever tube bender. Open-side type which slips over tube at any point. Makes smooth, tight radius bends up to 180° with minimum effort. No scoring or flattening of tubing. Calibrated to show angle of bend. Wide hook grips tubing securely.
Alan H
Reviewed in the United States on November 22, 2024
Sturdy and well made by a long established company. Produces nice clean bends. Handles provide the proper amount of leverage. Does exactly what it was designed to do. Made is USA.
Nana23
Reviewed in the United States on November 15, 2024
Worked well on 1/4 stainless steel brake lines. Much harder to bend than other lines.
Dima
Reviewed in the United States on June 7, 2021
Bending 1/4” stainless with this bender, like butter! I’m guessing steel or copper would be a breeze. Cushy handles are nice specially if you bending all day. Highly recommend!
DT
Reviewed in Canada on June 30, 2021
Used this bender to make a new set of transmission cooler lines. Straightening the raw tube is key in obtaining the best results when using a spool of bulk tubing. This bender worked perfectly for my application. Might not be so well suited for thick wall stainless steel tubing.
Troy G
Reviewed in the United States on July 14, 2020
I’ve used imperial benders for years and this one is no exception. Good quality and does a nice job. For those of you new to tubing benders.... learn what the markings are for on the handle. It will make your like easier...
chuck b.
Reviewed in the United States on January 6, 2020
Makes nice bends with good quality tubing. Cheap tubing will kink, not the tools fault, but my local Napa had some lesser quality tubing mixed in the bunch I got and the cheaper stuff kinked, the stronger tubing bent perfectly.
Stuart Bennett
Reviewed in Australia on January 2, 2020
Work really good
Morris J.
Reviewed in the United States on January 12, 2020
I honestly thought I was buying a quality tool. This thing is not up to the task of bending stainless steel. First, the handles are too short. I had to put one handle in a bench vise to be able to control the tool. Second, the clamp slips, causing bends to kink. I countered that problem with a set of vice grips I used as a positive stop (marring my tubing I might add). Finally, the die split on my third bend, probably trying to counter the tubing kinking. The die appears to be made from a weak cast material. If you're looking to bend stainless, keep looking. If you're bending something softer, buy a less expensive tool.
Dragonflier
Reviewed in the United States on April 23, 2020
A bit pricey, but worth every penny. The ability to make very tight bends in 3/16 brake line was worth the price I paid. Lines look professional and zero kinks. I’ve wasted my money on lesser quality benders and have been disappointed with each of them for various reasons. If you need to make tight bends up to 180 degrees (with as little as a 7/16” radius), then this is the tool for you. Sure, it only does one size, but it does it the best. Would I buy again? Absolutely!!
Mike Sumners
Reviewed in the United States on July 14, 2019
This tool made bending 3/8 stainless line quite easy. I previously owned a cheaper multi size smaller tubing bender and it was extremely difficult to use with 3/8 line. Definitely worth the cost of the tool to get good results.
Roy W Baker
Reviewed in Canada on July 29, 2018
just used this tool to bend 1/4 inch stainless brake, awesome should have this yrs ago
名無し
Reviewed in Japan on June 11, 2018
格安で売られてるものに対して別格な道具ですが、ちょっと高いと思う。
45K
Reviewed in Japan on April 12, 2014
配管工事はド素人ですが、軟質銅管で日用品を作っています。今まで４千円位のものを使っていましたが、どうしても気に入らなく、これに買い換えました。さすが安物とは違いました。管をくわえた時、上の0と下の0がピタッと合いズレません。目盛の「L」しか使っていませんが、これがまた正確。今まではいちいちノギスを当てて調整していましたが、これからは不要。また、溝が1/4インチ管とピッタリ合うため曲げによる扁平も少ない。取っ手部分（青色）もツルツルしていなく持ちやすい。道具はこうでなくっちゃ、と感心した次第。なお、今現在の商品の写真が違いますので、検討中の方は要注意。
Recommended Products
