Your cart is empty.
Your cart is empty.Product Description
Product Display
T-Deck Specifications
- For more programming information about the product, please refer to Github: github.com/Xinyuan-LilyGO/T-Deck
- T-Deck can't upload any sketch，Please enter the upload mode manually.
- Connect the board via the USB cable
- Press and hold the BOOT button , While still pressing the BOOT(On the trackball above the keyboard, press down) button
- Press RST button
- Release the RST button
- Release the BOOT button
- Upload sketch
Product Pin Diagram
Tips:
- If a microphone is used, the GPIOO button cannot be used
- If the sketch cannot be uploaded, then you need to press down the middle of the trackball, and then insert the USB, this means the chip is in the download mode, and then click to upload the sketch.
- T-Keyboard the programming and burning interface of ESP32C3 is located at the 6Pin header on the side of the RST button, and the order starts from the top of the RST button, which are 3V3, GND, RST, BOOT, RX, TX, You need to connect USB TO TTL externally to burn the keyboard firmware. For TTL without automatic download circuit, before powering on, short-circuit the BOOT Pin and GND, and then power on. At this time, T-Keyboard will enter the download mode. After the burning is completed, you need to disconnect GND and BOOT before running the program.
Shipping List
- 1 X T-Deck(Black Keyboard）
- 1 X Pin (6pin)
- 1 X Power cable
- 1 X 433/868/915MHz LTE antenna
Shipping List
- 1 X T-Deck(White Keyboard）
- 1 X Pin (6pin)
- 1 X Power cable
- 1 X 915MHz LTE antenna
Juan Romero
Reviewed in the United States on March 27, 2025
Works great.
Matt
Reviewed in the United States on March 26, 2025
I bought this when it first came out and it’s still going strong. 3-D print a case for it and haven’t had a single issue with it. I have a few other Lily products and I’m happy with all of them.
Squirrely Dan
Reviewed in the United States on February 19, 2025
I got this and some accessories before I found the model that comes with a case and gps. For most people, buy that model instead for an extra $3.There are some nice 3D printable cases for this device.As far as the device goes it works well. Meshtastic feels a little beta still. The touchscreen isn't utilized yet. It's easy to use and having a keyboard makes it feel more functional than the other devices.
Christopher Chevrier
Reviewed in the United States on February 18, 2025
It can be the hardest thing to program unless you follow directions well
Phil Hildner
Reviewed in the United States on January 9, 2025
Great clone of a blackberry for a LoRa transceiver. 3D printed a case for it, flashed it with Fancy Meshtastic. Added a 5000 mAh battery, a GPS unit and a 915 Mhz external antenna. Works very well.
Alfonso Faustino
Reviewed in the United States on January 2, 2025
The media could not be loaded.
cp2004
Reviewed in the United States on June 20, 2024
I was hesitant at first and thought I bricked my first one. Well after I set up the second they connected perfectly! Quality of the product is good I just need to print a case. The display is simple what’s it’s needed for. The units I purchased already came with Meshtastic preloaded in them and I flashed them to the newest version which was easy as pie! Now I’m in the test phase of distance since there are no nodes around me so I’ll be creating a network in my area. Performance of the application is great and easy to configure everything from your mobile device or via cable from the Meshtastic network!Definitely going to be purchasing more Lilygo devices to setup to expand my network and reach!TDecks arrive before estimated time as I knew they were back ordered. Already flashed with the 2nd latest Meshtastic update. 3D printed a case for all of them I ordered.Love it!
J MacDonald Ruffeno
Reviewed in the United States on May 31, 2024
Touch screen- ok.Roller ball - very sensitive.Keyboard - works
Recommended Products