Your cart is empty.
Your cart is empty.Product Description
Is there any advantages of the product?
✔ Material - Threaded rod made of 304 stainless steel, provides great corrosion resistance and antirust ability for long service life.Fully threaded rods are widely applied in many occasions.
✔ Fully Threaded Design - Neat and clear thread, exquisite workmanship, entire threaded design, allowing for a secure connection on both ends, which makes it great for applications where the rod needs to be fully engaged with nuts or other fasteners.
How to use it?
✔ Select the appropriate size threaded rod, connect the nut on the machine, and tighten it
What should I notice?
✔ All size above is measured by manual, please allow +/-0.1 inch error.
Specifications
- Type: Fully Threaded Rod
- Material: 304 stainless steel
- Thread: Right Hand Thread
- Easy Installation: Fully threaded rod stud is easy and convenient to use.
Fully All Threaded Rod
304 Stainless Steel Right Hand Thread Screw
Suitable for furniture mounting assembly fastening, screw into threaded nuts or tapped holes. Widely used for anchor bolts, clamps, hangers and U-bolts and many more projects where a metal rod with continuous threading or no head or fashioned tip is required
Application
Wide Application - The bar studs are commonly used for securing components and machinery in place and provide reliable support, such as used in the assembly of equipment, machinery, furniture, machine tools, etc. Also used for bolts, clamps, hangers, u-bolts, garden stakes and other projects where a metal rod with continuous threading.
Thing Guy!
Reviewed in Canada on March 23, 2024
Easy to use and saves time instead of using ready rod.
Zippy
Reviewed in the United Kingdom on February 3, 2024
This pack contains four rods threaded their entire 150mm length to M8, and four M8 nuts.I have a simulator rig made from extruded aluminium section, and this M8 rod is ideal for securing components to it. I've got several 3D-printed mounting blocks and brackets which are a bit flimsy on their own, so this rod strengthens them and makes them really easy to fit and remove when I switch between racing and flight simulator modes.If the rod is too long, it's easy enough to cut with a hacksaw.Take care opening the pack, as the nuts are loose inside! Despite the basic packaging (which only goes in the bin anyway), I highly recommend this product.
Customer
Reviewed in the United Kingdom on February 17, 2024
The ten pieces of threaded rod arrived in a taped up bubble-lined envelope that was taped shut, which kept them all together and protected during shipping. There were exactly ten pieces inside and all of them measured 150mm long and are of consistent quality. They’ve been cut squarely and have been reasonably well deburred to the point that threading a nut onto them wouldn’t be an issue. I had no problems getting an M8 nut onto any of the threaded sections at all from either end of the rods. Despite the fact that these have been tidied up a bit there is still some roughness so I'd recommend taking a few seconds to deburr them if that's a concern.Ultimately, these are as expected and accurate to the product description and are well worth considering if you’re after some pre-cut lengths of M8 all-thread on short notice. My only minor complaint is that £14.99 is a lot of money for a total length of 1.5 metres rod when you can get several metres for around the same cost.
Pixelated88
Reviewed in Canada on December 30, 2023
A million uses, so I won't go into what you can do with them. Their M8 sizing is correct and perfect threads along their entire length. Make sure you have the ability/facility to cut stainless easily. This won't be too much fun with a hand-held hack saw.Using these with pneumatic cylinders.
ZDitto
Reviewed in Canada on November 6, 2023
Not much to say really, they are well made, nice quality steel, no defects, and the ends are properly deburred. Should work well.
Clint Martin
Reviewed in the United States on November 5, 2023
No issues with these threaded rod pieces. They are as described - M8 1.25's, good stainless, no burrs on the threads. I'd buy these again for small projects.
JAWs
Reviewed in the United States on October 30, 2023
These work well for use with end bearings and extending the distance from the control arm to the end of the arm. Plan on using them for controlling steering on a big PowerWheels project.
Recommended Products