Your cart is empty.
Your cart is empty.
The Mitutoyo 050084-10 depth base attachment has a 4" base length and is suitable for use with Mitutoyo 4 to 8" (100 to 200mm) vernier and dial calipers (sold separately). The knurled locking clamp holds a caliper securely. The base is made of steel and the measuring face is ground for flatness. This depth base is suitable for precise measurement in a variety of manufacturing, machining, and mechanical engineering applications.
Depth gauges are precision measuring instruments used to determine the depth of any shape that has a step, groove, or slot. These gauges often take the form of sliders that travel on a measuring beam or rods, are moved to position by hand, and then adjusted with a calibrated screw. The base of the gauge rests at the top of the shape whose recession is to be measured, while the beam or rods extend to the bottom of the recession to determine the measurement. Gauge position is read from a graduated scale, dial, counters, or an electronic display.
Mitutoyo manufactures precision measuring tools, metrology equipment, and related systems. The company, founded in Tokyo in 1934, formed Mitutoyo America Corporation in 1963 with headquarters in Aurora, IL.
James
Reviewed in the United States on February 15, 2025
An egregious price given the country of manufacture.
Joshua Michael Gibbs
Reviewed in the United States on September 20, 2024
This has made measuring depth dimensions with (+- .005) tolerances so much easier and way more accurate. I've checked it on a 1-2-3 block and it's within (+- .0005). Very stable as you can see I'm measuring the thread depth in this picture and I've always been paranoid when checking depth dimensions with the depth check on my calipers it doesn't feel right half the time but with this depth base i can instantly feel that it has sat flat against whatever I put it on which gives me assurance that whatever I'm checking is going to be what it says it is. It has a tapered screw lock that presses it to the back of the caliper slot and to the side securely the caliper slot is precision ground as well as the base. If your thinking about buying this I highly recommend it, the returns for the amount of money is absolutely worth it! Well done mitutoyo as always.
中西孝夫
Reviewed in Japan on June 15, 2023
ワーク面に傷が入っています。あくまでも計測機器関連商品なので、納得できません。計測に影響無いのでＯＫということでしょうか？返品交換しても同じような有様でした。
JJI
Reviewed in the United States on December 5, 2023
Bought this for my 10” mitutoyo calipers. It’s a perfect fit on my 10” digital calipers and produces very repeatable measurements. Attaching and removing is very simple and fast. However it is too big to fit well in the case calipers case without flopping around
Micah Carrillo
Reviewed in the United States on November 27, 2023
I liked how well it was built. It is a very well made attachment. It is very large though and this may or may not be a negative. It turns the caliper landing into near the same size as a depth mic so while it may be big it also registers firmly and seems very accurate. I was getting good readings much more repeatable with this than none at all. The weight and size keeps my caliper from tipping or walking off a few thousands from square which was the point all along.
shrifty
Reviewed in the United States on December 19, 2022
The heaviness of this base gives it enough sturdiness that it will stand on it's own in the vertical position using a six inch caliper while recording measurements, something those other much lighter ones will not do.
Fabio Passeto
Reviewed in the United States on April 26, 2022
This attachment provides a wide and solid contact area which is much better than other similar products which are made of smaller and thinner material.The attachment to the caliper is through a taper washed compressed against the caliper base. It looks like it has a too big clearance to the caliper but the fit is good and precise.
Erendira Paramo
Reviewed in Mexico on February 23, 2020
Todo bien. Gracias
スバル信者
Reviewed in Japan on December 12, 2020
以前、自作してみたことがありましたが、ノギスの固定がいまいちでした。オリジナルは、しっかりと固定でき、作りこみの質の高さを実感しています。ノギスの使用範囲が広がるパーツです。
ST
Reviewed in Canada on August 31, 2017
Quality is good, but the unit I received was marked "Made in China", it's disappointing.I have to keep attachment separately from caliper in my toolbox, because it doesn't fit in the specially designed place in Mitutoyo plastic case.In description must be "It doesn't fit in standard Mitutoyo plastic case".
rj
Reviewed in the United States on May 23, 2016
Doesn't fit the 6" AOS caliper (probably most popular Mit. caliper). There is quite a lot of leftover space, 5mm at least, which I think may be needed to clear the screw at the end of the caliper. While the thumbscrew does hold the caliper securely, you wonder if you really got it on square and securely.To compare products, the iGaging depth base attachment fits the iGaging 6" calipers absolutely perfectly.The iGaging depth attachment is smaller but still bit larger than the Mit. AOS 6" caliper so in theory it should fit, but the engagement is terrible so I bought the Mit. base thinking the fitment would be spot-on. Oh well.
BAZMick
Reviewed in the United States on January 7, 2015
Great, much cheaper than buying a whole new depth gauge
Recommended Products
