Your cart is empty.
Your cart is empty. Excellent quality: Our carburetor is an excellent choice for replacing defective parts, ultra-high performance, helping your car run at peak performance.
Package:
1x carburetor, 1x Gasket, 1x manual choke replacement, 1x throttle arm replacement, 1x fuel inlet plug, 4x Bolts. As shown in the picture.
Fits for:
Fiat Renault Ford VW Dodge Jeep
Toyota Pickup Daewoo Lada Seat Opel
BMW 2002 1968-1976 E10
BMW 2002tii 1971-1974 E10
BMW 320i 1977-1983 E21
Mercedes-Benz 280 1973-1976 114.060
Mercedes-Benz 280C 1973-1976 114.073
Specification：:
Main Venturi - 27
Main Jet - 145
Emulsion Tube - F50
Idle Jet - 45
Float Level - 40/52.5
Type: Automatic choke/Electric Choke
SATISFACTION SERVICE:
We will provide you with quality products and services, if you have any questions or dissatisfaction, please feel free to contact us and we will get back to you as soon as possible.
james
Reviewed in the United States on March 6, 2025
Didn’t need anything except an idle adjustment
Bradley Burleson
Reviewed in the United States on September 9, 2024
I have a genuine Weber 38/38 on my MGB. A winter project is going to be rebuilding it. For the price of this, I figured it was worth a shot to have this to put on the B so I could still drive it while rebuilding the old Weber. It is almost identical when placed side by side. Build quality is good. The linkage on this is a little bit different as it has multiple places you can attach the throttle cable (which I actually like better), and it doesn't say Weber, otherwise they are identical. I pulled the Weber bolted this right on, hooked everything up and the car fired up immediately. It was running a bit rich, so I leaned it out some and that'd all. I have been driving it for a couple of weeks now with this carburetor and it is running flawlessly. Better than ever. I can really see that the Weber was ready for a rebuild. After I rebuild, I'll pull this and throw it on the shelf, ready to go on another project or back on the MGB if needed. Recommend.
David Drake
Reviewed in the United States on August 4, 2024
Installed on my ‘79 MG Midget. Works great right out of the
Blair
Reviewed in the United States on June 26, 2024
Have installed but not turned over engine yet so no review on performance.However I did measure up against the original Webber Carb and it is spot on.Very happy with price and how well it fits.
J. Porter
Reviewed in the United States on May 31, 2024
EDITED:What can I say… I’m a glutton for punishment and curiosity got the best of me so I did buy another one of these carbs. This second carburetor was machined much better and had far less debris. I cleaned it up, set the float, staked the throttle plate screws, replaced the idle screws with some o-ringed IDF screws and installed it on my AMC 258. This carb was much more consistent than my old worn out Weber. The idle jets are spot on for me but be aware that you cannot swap them with real Weber idle jets if they aren’t correct for your application.The engine idles great but was running too rich at cruise for me. I was able to replace the main jets with smaller authentic Weber jets. The original jets do not have any indication as to their size but after some trial and error I would guess them to be 140-145s. The jeep runs fantastic with this new set up!I would still strongly suggest that you disassemble and check these carbs before installing them on your engine. In my opinion the debris I found in the pictured carburetor could have caused major issues in this engine had I just mounted and ran it.ORIGINAL REVIEW:As advised in an earlier review, I took this carburetor apart to check for debris before spending the time to install it on my engine. I was appalled to find that one of the air corrector ports was stripped out and/or incorrectly machined. I also found A LOT of metal flakesand shavings in the interior passages of this carburetor which could have lead to clogged jets/ports and possibly metal debris in my engine.A return/replacement was set up the same day I received the unit. Later I received an email stating "supply chain issues" were going to delay shipment of the replacement with no delivery date in sight, yet when I look at the purchase page it shows that another one can be bought and delivered the very next day?I too read the reviews and think these things won't happen to me but am glad I checked before installing. Good luck to those of you who are brave enough to purchase this carburetor and install it without checking it first!
fred m.
Reviewed in the United States on February 20, 2024
Got to admit I was worried because of the low price. But, it works fine with very minimal fitting.
B22kturbo
Reviewed in the United States on October 28, 2024
Bolted right on in place of the 32/36 that was on it and improved the performance considerably. Jetting worked good on the b2200 with a header.
Brandon
Reviewed in the United States on November 4, 2023
Easy swap from Weber 32/36. Runs fantastic with no adjustment. Would absolutely recommend to any Jeep owners that are looking for an upgrade.
Recommended Products
