Your cart is empty.
Your cart is empty.The Performance Tool W54209 Grease Fitting Cleaning Tool is the perfect solution for cleaning solidified grease from Zerk fittings. Whether you're working on angled or straight fittings, this versatile tool has you covered. Simply draw oil or grease into the tool, place it on the fitting, and strike with a hammer for quick and easy cleaning. Made with high-quality materials, this cleaning tool is built to last and can withstand the demands of heavy-duty use. Achieve professional results in a fraction of the time with this must-have tool for anyone working with grease fittings. Get the Performance Tool W54209 Grease Fitting Cleaning Tool today!
AJ Nash
Reviewed in the United States on March 10, 2025
The gap between the plunger rod and the housing is too large and grease/oil comes shooting out around the rod rather than into the grease fitting. Big mess. I do not recommend.
ian fillingham
Reviewed in the United Kingdom on February 13, 2025
Great service
John LeBlanc
Reviewed in the United States on September 4, 2024
Good price works well
JW Frazier
Reviewed in the United States on June 9, 2024
Friend said it worked great for what he needed it for
Bob Dodge
Reviewed in Canada on December 29, 2024
Grease Fitting Cleaning Tool Is garbage. Does no fit onto a grease zerk with a seal. Simply sits over it. Bore is rough and won’t hold liquid cleaner. No O ring. Waste of time.
The Ahern’s
Reviewed in the United Kingdom on December 26, 2024
The pickup axel joint squeaked and needed grease but its nipple was blocked, tried a blow torch, couldn’t unscrew it (the nut stands about 2-3mm out and couldn’t get get a spanner on it), short of changing the whole axels joint or taking it to a garage I resorted to this. And it worked. Filling it is messy, but hold it over the nipple and whack the end with a lump hammer and it filled it.
Bryan
Reviewed in the United States on December 17, 2024
Perfect
Dan K.
Reviewed in the United States on December 10, 2024
I fooled around with this worthless thing for about an hour. I tried to fill it with PB Blaster and it leaks out . Then I tried to get it filled with grease, so it wouldn’t leak. All it does is squirt everywhere else but into the grease zerk. What a freaking mess! I hucked it straight into the dumpster ! Wasted my time and money.
Customer
Reviewed in the United States on January 27, 2024
Clean the grease fitting well because the tool does not lock onto the fitting, and you just hold the tool firmly in place and the hammer strike seals it to the fitting. Easier to unscrew the fitting end, pull out the plunger, fill the tool with oil, and replace the fitting end. If the tool has air in it along with grease or oil, the plunger stroke will be longer and the hammer strike pressure will be lower. If the tool slips off the fitting before the hammer strike, grease or oil will go everywhere.
Marco
Reviewed in Italy on April 7, 2024
Attrezzo scadente e non funzionante. Prima di tutto non si adatta agli ingrassatori ZERK dunque lo puoi solo poggiare sopra l'ingrassatore zerk. Inoltre al momento dell'uso l'olio fuoriesce dalla parte superiore con il pericolo che ti vada negli occhi. Ripeto, attrezzo davvero scadente e inutile al suo scopo. Evitate di comprarlo ..soldi buttati.
Steve Harvey
Reviewed in the United Kingdom on March 28, 2021
Does the job
C n C Computers
Reviewed in the United States on September 30, 2019
I bought this so I could grease the zerks on the wheels of my garden tractor since they are in a tight spot. It works and gets the job done, but it does leak grease out of the sides and at the male end. This is just a 90 tube, with a female grease couple at one end, and a male zerk at the other end. You do not screw this onto your grease gun hose. That was somewhat disappointing since if it did screw on, it would probably not leak at all. If I bought another one, I would get one that has a screw connection on the gun side, rather than a zerk, but it does do what it was intended as long as you don't mind getting grease all over the end of the tip.
PowderMonkey
Reviewed in the United States on October 5, 2018
This is one of those products that need to be in your toolbox because eventually you'll need one! It's now a part of my zerk fitting tool box (ok it''s actually an old cigar box re-tasked) Havent used it yet and will update later! Seems ok- a bit crudely made, but for the price- if it works when I actually need it- will be worth it's weight in gold!
Recommended Products
