Your cart is empty.
Your cart is empty.Lift chair replacement remote controller with heat and massage button adjustments. 9 pin plug connection.
John leonard
Reviewed in the United States on March 25, 2025
Fixed my mom's chair and saved us a lot of $ on a new one.
Stephen Riley
Reviewed in Canada on March 13, 2025
IT WORKED …5 star
Julie
Reviewed in Canada on February 21, 2025
Great quality. Exactly what we were looking for. The only thing was the input screws weren't long enough but we just used the old ones from our previous remote.
Patricia
Reviewed in the United States on September 11, 2024
This was a perfect match for my easy lift chair. It was like I had the original back except this one works
Vince
Reviewed in Canada on August 10, 2024
It was easy to install on the chair and works great
Randy Linder
Reviewed in the United States on December 18, 2024
Lift chair
Bob C
Reviewed in Canada on November 18, 2024
The chair is like new.Simple install.
Jason reeves
Reviewed in the United States on October 10, 2024
It shipped very fast, was easy to install and worked very well.
Jksmith
Reviewed in the United States on April 16, 2024
Thought I was going to have to buy my grandmother a new chair! Nope this did the trick! Perfect fit and works great!
Stephen O'Connor
Reviewed in the United States on July 20, 2023
The old hand controller for my recliner/lift chair was balky and sporadically working. I was thrilled to find a replacement.I purchased it and was delighted to see it light up.The only issue was that the thumb screws affixing the controller to the junction box was a bit short. Simply salvage the screw from your old controller
Vicky Schoeneweis
Reviewed in the United States on February 24, 2021
I bought my lift-chair used, and I am NOT mechanically inclined. When my hand control quit working, I got the part number off the back, and ordered this part. It arrived yesterday. This morning I turned my lift chair over, and followed the old wire to the motor. :o That cord didn't have the same plug on the end. So I came back to the reviews where people kept mentioning the "junction box" and that the cord plugged into the junction box. BUT I don't see a junction box ANYWHERE on the bottom of the chair. But now I look at the picture so I know what it looks like. SO, I get a flashlight and look up to the back of the chair. BINGO, there it is! I had to pull the staples out of the back chair cover to access the junction box, but after that, it was just a matter of unplugging the old control and plugging the new one in. Instead of running the coiled cord back down to the floor and back up to the pocket, I just ran it through the back right next to the junction box, hammered the staples back down and now there's plenty of cord. I can still store the control in the side pocket, but it will just sit on the arm of the chair with no undue pressure pulling on the ends of the wires now. Like I say, I am a 65 year old woman who is NOT mechanically inclined, but I was able to do this and only had to use one band-aid where one of the staples caught my arm. The chair is back in use and working just fine. TOOLS NEEDED: flashlight, hammer, one or two band-aids. :)
ChrisB
Reviewed in Canada on December 22, 2021
I had ordered from this retailer before and had a good experience, so I wasn't worried about purchasing from them again. I should have ordered this controller when I had ordered the control module previously as the price has gone up significantly. When you order this, expect a long lead time as it is coming from the States and takes quite a while.I would definitely order from them again (lets hope no more parts break on this chair).
Bruce S.
Reviewed in the United States on February 26, 2017
For the price this is an excellent after market chair control that installed easily and works well. We did research these online before purchasing and this is by far the most reasonably price. Some other sites have them listed at 3 X the price of what we paid here for the exact same thing. And if your wondering if this will replace your original Tranquil Ease 7051-3 hand control, yes it will. This was the big question we had before purchase. If the plug on your remote has a 9 pin "D" shaped serial port plug, with 2 self contained screw hold-downs that secures the plug into the control box, then this unit should work on your chair. Many here have described this plug as being rectangular in shape, but it is actuality a D shaped serial port plug (shaped like a long narrow capital D surrounding the pins), just like you use to see on many computer applications (such as the old stye inkjet printers). Our only negative about this product, which also applies to the oem hand controller that came with the chair when new, is that there isn't enough cord to adequately use it without putting unnecessary strain on the coiled cord or hand unit. This is why we had to replace our original in the first place. The pulling on the coiled cored over the years eventually causes the wires to pull out of the hand controller; so about 6 more inches of cord would have been nice. Being a design flaw we didn't deduct any star ratings from the seller for this minor inconvenience and figure only time will tell if this becomes a recurring issue. But in no-way does this reflect the fault of the seller, their provided service and their great price compared to others. We were just hoping the manufacture would have taken this into consideration when re-designing these.
Recommended Products
