Shopping Cart

Your cart is empty.

Your cart is empty.

Dual Frequency IR Tube IR Receiver Extra IR Receiver for IR (Infrared) Repeater Kit/Remote Control Extender Kits

4.8 (4) Write Review
Free shipping on orders over $29.99

$15.00

$ 6 .99 $6.99

In Stock

About this item

  • Please confirm that this is compatible with your device from the - "Tested and works with the following" section in this advertisement before you purchase.
  • Wide band IR receives IR from many types of remotes. Our Peephole IR receiver for the HDTVHookup Products Repeater System is designed to be mounted in a wall, cabinet or door so you have more sleek, streamlined look to your setup!
  • Dual Frequency - This is only needed if you have a HD Cable or Satellite receiver that operates at a higher frequency then normally found. Over the last few years many new cable and satellite boxes from SA, DirecTV, Dish and Uverse have emerged operating at a higher IR frequency then before.
  • Easily Hidden and Installed on any of OUR IR Repeater Systems
  • Our IR sensors can receive signals from 25’ away and up to a 45° angle from the remote control. Can be used with any IR remote controls.


Product Description

IR Remote Control IR Tube Receiver

IR Receiver Tube for Deluxe IR Receiver Repeater System

  • Dual Frequency IR Receiver - 34Khz to 60Khz - With Blue Light Confirmation Blink
  • Our IR Receiver is a perfect Accessory to hide your IR Repeater Extender Systems – Our Tube IR receiver for the HDTVHookup and Unique Products Online Repeater kits. Its unique design allows it to be mounted in a wall, cabinet or door so you have a more professional look to your setup! This will require you drill a ½” hole in your wall or cabinet, slide the Tube receiver in and tighten using a 5/8” wrench or your fingers.
  • Our IR Receiver can receive signals from 25’ away and up to a 45° angle from the remote control. This can be used with any IR ( Infra-Red ) remote control. Cable is 10’ long.
    • 40ft @ 38Khz
    • 25ft @ 56Khz
  • Works with any Make model of remote controls as long as they use Infrared technology.
  • Tested with IR Repeater Systems sold under HDTVHookup, Unique Products Online, TNP Ir repeater system, Sewell Direct Blast IR, BAFX Products Single Zone IR Repeater / Remote Control Extender Kit only!
  • Plug and Voltage information.
    • Tip Signal
    • Gnd is Ring
    • +12V Dc is the Sleeve
  • Installation is simple.
    • Just plug it into the Connecting block on the IR Repeater Extender System where it says IR Receiver

Tested and works with the following –

  • HdtvHookup Models - Item number- Deluxe IR 1204 Repeater system Asin - B0039CGCO4 HdtvHookup In Wall System Item number- HdtvHookup IRS6A Asin - B003CAVQLW HdtvHookup System- Item number-DLXPLUSINWALL Asin - B007S9FY2K HdtvHookup System – Item Number- HdtvHookup1204P – Asin - B00GHM4Z9M
  • Unique Products Online – Item number - DLX IR System – Asin - B005P0AOWY Unique Products Online In Wall system - Item number- IRS-6A Asin - B07W6G5RDS
  • Cables Direct Item number - IRrepeatersystem 1204p Asin - B0016PM63W
  • C2G Cables to Go - Item number 40430
  • TNP Products - Item number - A-1204A Asin - B013318WFW
  • Cmple - Item number - 1183-Amazon Asin - B00DY87UC6
  • Ensigear Asin - B078GN4BHX
  • Sewell - Item number- SW-29311 Asin - B004FJV8EE Sewel - Item number- SW-29309 Asin - B004G7SXKM Sewell In wall IR System Item number- SW-29310 Asin - BB004G7JSTW
  • Cables to go C2G - -C2G 40478 Item number – 40478 Asin - B003UYU3QO

Anne C. Morris
Reviewed in the United States on July 23, 2024
I needed an IR Receiver that could be installed in a wall that would integrate with an IR Repeater System. At first it did not work. After peering over the documentation that came with the IR Receiver, I determined that the pin-out was Tip-Output, Ring-VDC-, and Sleeve-VDC+. In other words, the Ring and Sleeve connections were reversed when compared to my IR Repeater System. In all my years of audiovisual work, I have never seen a device where the Sleeve was not negative or ground. I made an adapter cable with a 3.5mm Male and a 3.5mm Female, switching the Ring and Sleeve connections. The device worked perfectly after I did this. Not an ideal solution, but I was pressed for time to get the install done. If not for the pin-out situation, this would be a 5-star rating.
Mary & Lou
Reviewed in the United States on May 20, 2024
The media could not be loaded.
Lawrence J. Przywara
Reviewed in the United States on January 19, 2024
Works with Aton DLA4 multi-room amplifier.
Dwight H.
Reviewed in the United States on September 29, 2023
I was hopeful but it never worked.